Incorporated changes for release 1.3.4

RPiSetup/bookworm/ap-setup-nmcli.sh

@@ -0,0 +1,108 @@
+#!/bin/bash
+
+#    ap-setup.sh
+#    OpenDRS Online Discrepancy Reporting System
+#    Copyright (C) 2022  Rod Wright
+
+#    SPDX-License-Identifier: GPL-2.0
+
+# Wireless Access Point Raspberry Pi Setup
+current_user=`whoami`
+if [ "$current_user" != "root" ]
+then
+	echo "You must have root privileges to run this setup."
+	echo "Try 'sudo ./ap-setup-hostapd.sh'"
+	exit 1
+fi
+source ../common.sh
+echo ""
+getmodel
+echo ""
+getosrelease
+echo ""
+getarch
+echo ""
+if [ $arch_32_64 -eq 64 -a "$ismodel3" = "true" ]
+then
+    echo "Raspberry Pi 3 hardware is known to have problems with acting as a"
+    echo "wireless access point when 64 bit kernels are used. If you intend for"
+    echo "this terminal to act as a wireless access point, you should stop here,"
+    echo "power off, remove the microsd card and re-image using a 32 bit version"
+    echo "of Raspberry Pi OS."
+    echo -n "Ignore and [c]ontinue or [A]bort? [c/A]: "
+    read archabort
+    if [ "$archabort" = "C" -o "$archabort" = "c" ]
+	then
+        echo ""
+        echo "Continuing with installation."
+    else
+        echo ""
+        echo "Aborting installation."
+        exit 0
+    fi
+fi
+echo ""
+echo "If this terminal connects to a network using ethernet, it can be configured"
+echo "as a wireless access point for other terminals. Would you like to configure"
+echo -n "this terminal as an access point? [y/N]: "
+read wapconf
+if [ "$wapconf" = "Y" -o "$wapconf" = "y" ]
+then
+	echo "Configuring as wireless access point."
+	echo ""
+	echo "Copying files..."
+	chmod +x apsetup/usr/local/bin/*
+	cp -v apsetup/usr/local/bin/* /usr/local/bin
+	cp -Rv apsetup/etc/* /etc
+	echo ""
+	wapssidok=0
+	while [ "$wapssidok" -ne 1 ]
+	do
+		echo "This access point will need an SSID. This is what will appear"
+		echo "as the name of this terminal when other devices connect."
+		echo -n "Please enter the desired SSID for this access point:  "
+		read wapssid
+		if [ "$wapssid" = "" ]
+		then
+			echo "SSID cannot be blank. Try again."
+		else
+			wapssidok=1
+		fi
+	done
+	wappassok=0
+	while [ "$wappassok" -ne 1 ]
+	do
+		echo "You will need to set a passphrase for this access point. It should"
+		echo "be at least 8 characters in length and cannot be blank."
+		echo -n "Please enter the desired passphrase for this access point:  "
+		read wappass
+		wappasslen=`echo -n $wappass | wc -m`
+		if [ "$wappass" = "" -o "$wappasslen" -lt 8 ]
+		then
+			echo "Passphrase doesn't satisfy requirements above. Try again."
+		else
+			wappassok=1
+		fi
+	done
+	# Create network bridge interface
+    nmcli connection add type bridge con-name 'Bridge' ifname bridge0
+    # Add ethernet connection to the bridge
+    nmcli connection add type ethernet slave-type bridge con-name 'Ethernet' ifname eth0 master bridge0
+    # Create wireless interface and add it to the bridge
+    nmcli connection add con-name 'Hotspot' ifname wlan0 type wifi slave-type bridge master bridge0 \
+    wifi.mode ap wifi.ssid $wapssid wifi-sec.key-mgmt wpa-psk \
+    wifi-sec.proto rsn wifi-sec.pairwise ccmp \
+    wifi-sec.psk $wappass
+    # Activate bridge
+    nmcli connection up Bridge
+    # Activate access point
+    nmcli connection up Hotspot
+	echo ""
+	echo "Wireless access point setup is complete."
+	echo ""
+	echo -n "Press enter key to continue..."
+	read cont
+else
+	exit 2
+fi
+